1605 east rodney french blvd. new bedford, ma 02744 (508) 996-8564, fax (508) 996-3830 http://www.cornell-dubilier.com e-mail: cdenb@cornell-dubilier.com 1.030 cornell dubilier your source for capacitor solutions chip and smt capacitors high-frequency, high-stability chip for instruments and rf with self-resonant frequencies typically above one gigahertz for popular rf capacitance values and with a q above 2,000, type mc capacitors are the answer for high-frequency applications like flight radio and cable television. the natural mica dielectric retains its high-q to many megahertz, so higher and higher frequency applications are limited by the circuit inductance, not the type mc capacitor. performance highlights ? voltages: 100 vdc, 500 vdc, and 1000 vdc ? capacitance range: .5 pf to 2,000 pf ? capacitance tolerance: 0.25% to 5% ? temperature range: C55 c to +125 c ? low impedance to beyond 1 ghz ? near-zero capacitance change, all environments ? available in tight tolerance exact values ? easy to attach to printed circuit boards ? case sizes 0805, 1210, 1812, and 2220 ? handles pulses with dv/dt>20,000 v/ m s ? withstands 200% rated voltage ratings cap catalog case pf number type 100 vdc 1 mc08ca010d 0805 2 mc08ca020d 0805 3 mc08ca030d 0805 4 mc08ca040d 0805 5 mc08ca050d 0805 6 mc08ca060d 0805 7 mc08ca070d 0805 8 mc08ca080d 0805 9 mc08ca090 d 0805 10 mc08ca100d 0805 12 mc08ea120j 0805 15 mc08ea150j 0805 18 mc08ea180j 0805 20 mc08ea200j 0805 22 mc08ea220j 0805 24 mc08ea240j 0805 27 mc08ea270j 0805 30 mc08ea300j 0805 33 mc08fa330j 0805 36 mc08fa360j 0805 39 mc08fa390j 0805 43 mc08fa430j 0805 47 mc12fa470j 1210 50 mc12fa500j 1210 51 mc12fa510j 1210 cap catalog case pf number type 100 vdc 56 mc12fa560j 1210 62 mc12fa620j 1210 68 mc12fa680j 1210 75 mc12fa750j 1210 82 mc12fa820j 1210 91 mc12fa910j 1210 100 mc12fa101j 1210 110 mc12fa111j 1210 120 mc12fa121j 1210 130 mc12fa131j 1210 150 mc12fa151j 1210 160 mc12fa161j 1210 180 mc12fa181j 1210 200 mc12fa201j 1210 220 mc12fa221j 1210 240 mc12fa241j 1210 250 mc12fa251j 1210 270 mc12fa271j 1210 300 mc12fa301j 1210 330 mc12fa331j 1210 360 mc12fa361j 1210 390 mc12fa391j 1210 430 mc12fa431j 1210 250 mc18fa251j 1812 270 mc18fa271j 1812 cap catalog case pf number type 100 vdc 300 mc18fa301j 1812 330 mc18fa331j 1812 360 mc18fa361j 1812 390 mc18fa391j 1812 430 mc18fa431j 1812 470 mc18fa471j 1812 500 mc18fa501j 1812 510 mc18fa511j 1812 560 mc18fa561j 1812 620 mc18fa621j 1812 680 mc18fa681j 1812 750 mc18fa751j 1812 820 mc18fa821j 1812 910 mc22fa911j 2220 1000 mc22fa102j 2220 110 0 mc22fa112 j 2220 120 0 mc22fa122 j 2220 1500 mc22fa152j 2220 1800 mc22fa182j 2220 200 0 mc22fa202 j 2220 type mc, surface-mount mica chip capacitors 8942 1.030-1.034 4/3/2000 6:17 pm page 30 222 0 m c 22 f a 222 j 2220
1605 east rodney french blvd. new bedford, ma 02744 (508) 996-8564, fax (508) 996-3830 http://www.cornell-dubilier.com e-mail: cdenb@cornell-dubilier.com 1.031 chip and smt capacitors cornell dubilier your source for capacitor solutions type mc, surface-mount mica chip capacitors ratings typical characteristic curves q vs. capacitance capacitance vs. frequency q vs. frequency % capacitance change vs. temperature resonant frequency vs. capacitance cap catalog case pf number type 500 vdc 1 mc12cd010d 1210 2 mc12cd020d 1210 3 mc12cd030d 1210 4 mc12cd040d 1210 5 mc12cd050d 1210 6 mc12cd060d 1210 7 mc12cd070d 1210 8 mc12cd080d 1210 9 mc12cd090d 1210 10 mc12cd100d 1210 12 mc12ed120j 1210 15 mc12ed150j 1210 18 mc12ed180j 1210 20 mc12ed200j 1210 22 mc12ed220j 1210 24 mc12ed240j 1210 27 mc12ed270j 1210 30 mc12ed300j 1210 33 mc12fd330j 1210 36 mc12fd360j 1210 39 mc12fd390j 1210 43 mc12fd430j 1210 47 mc12fd470j 1210 50 mc12fd500j 1210 51 mc12fd510j 1210 56 mc12fd560j 1210 62 mc12fd620j 1210 68 mc12fd680j 1210 75 mc12fd750j 1210 82 mc12fd820j 1210 91 mc12fd910j 1210 100 mc18fd101j 1812 110 mc18fd111j 1812 cap catalog case pf number type 500 vdc 120 mc18fd121j 1812 130 mc18fd131j 1812 150 mc18fd151j 1812 100 mc12fd101j 1210 110 mc12fd111j 1210 120 mc12fd121j 1210 130 mc12fd131j 1210 150 mc12fd151j 1210 160 mc18fd161j 1812 180 mc18fd181j 1812 200 mc18fd201j 1812 220 mc18fd221j 1812 240 mc18fd241j 1812 250 mc18fd251j 1812 270 mc18fd271j 1812 300 mc18fd301j 1812 330 mc18fd331j 1812 360 mc18fd361j 1812 390 mc18fd391j 1812 430 mc18fd431j 1812 470 mc18fd471j 1812 500 mc22fd501j 2220 510 mc22fd511j 2220 560 mc22fd561j 2220 620 mc22fd621j 2220 680 mc22fd681j 2220 750 mc22fd751j 2220 820 mc22fd821j 2220 910 mc22fd911j 2220 1000 mc22fd102j 2220 1100 mc22fd112j 2220 1200 mc22fd122j 2220 cap catalog case pf number type 1000 vdc 1 mc12cf010d 1210 2 mc12cf020d 1210 3 mc12cf030d 1210 4 mc12cf040d 1210 5 mc12cf050d 1210 6 mc12cf060d 1210 7 mc12cf070d 1210 8 mc12cf080d 1210 9 mc12cf090d 1210 10 mc12cf100d 1210 12 mc12ef120j 1210 15 mc12ef150j 1210 18 mc12ef180j 1210 20 mc12ef200j 1210 22 mc12ef220j 1210 24 mc12ef240j 1210 27 mc12ef270j 1210 30 mc12ef300j 1210 33 mc12ff330j 1210 36 mc12ff360j 1210 39 mc12ff390j 1210 43 mc12ff430j 1210 47 mc12ff470j 1210 50 mc12ff500j 1210 cap catalog case pf number type 1000 vdc 100 mc22ff101j 2220 110 mc22ff111j 2220 120 mc22ff121j 2220 130 mc22ff131j 2220 150 mc22ff151j 2220 160 mc22ff161j 2220 180 mc22ff181j 2220 200 mc22ff201j 2220 220 mc22ff221j 2220 240 mc22ff241j 2220 250 mc22ff251j 2220 270 mc22ff271j 2220 300 mc22ff301j 2220 330 mc22ff331j 2220 360 mc22ff361j 2220 390 mc22ff391j 2220 430 mc22ff431j 2220 470 mc22ff471j 2220 500 mc22ff501j 2220 510 mc22ff511j 2220 560 mc22ff561j 2220 620 mc22ff621j 2220 680 mc22ff681j 2220 750 mc22ff751j 2220 820 mc22ff821j 2220 910 mc22ff911j 2220 1000 mc22ff102j 2220 1100 mc22ff112j 2220 1200 mc22ff122j 2220 1500 mc22ff152j 2220 impedance vs. frequency 8942 1.030-1.034 4/3/2000 6:17 pm page 31
1605 east rodney french blvd. new bedford, ma 02744 (508) 996-8564, fax (508) 996-3830 http://www.cornell-dubilier.com e-mail: cdenb@cornell-dubilier.com 1.032 cornell dubilier your source for capacitor solutions chip and smt capacitors type mc, surface-mount mica chip capacitors speci?cations marking voltage color brown=100 vdc r1 green=500 vdc brn/grn=1000 vdc capacitance code base code base code value ltr. value ltr. 10 a 40 d 11 b 43 r 12 c 45 e 13 d 47 s 15 e 50 f 16 f 51 t 18 g 56 u 20 h 60 m 22 j 62 v 24 k 68 w 25 a 70 n 27 l 75 x 30 m 80 t 33 n 82 y 35 b 90 y 36 p 91 z 39 q multiplier code no. x 0.1 0 x 1 1 x 10 2 x 100 3 x 0.01 9 capacitance is within tolerance when measured as follows: 1C1000 pf @ 1 mhz > 1000 pf @ 1 khz dissipation factor is no more than 0.1% when measured as above. quality factor (q) is as follows when measured at 1 mhz. capacitance min. q range 1 to 80 pf 500 to 3000 >80 pf 3000 insulation resistance is no less than 100 g w when measured at 100 vdc. withstanding voltage is two times the rated voltage and can be applied up to 5 seconds without damage. life test: subject capacitors to 125 3 c with 1.5 times rated volt- age applied for 2000 (+72,C0) hours. there will be no visual dam- age and the capacitors will meet the limits of the table below. vibration resistance: subject the capacitors to simple harmonic motion with an amplitude of 0.06 inches; vary the frequency uni- formly from 10 to 55 hz and return to 10 hz, all in one minute. repeat that cycle continuously for two hours in each of three mutually perpendicular directions. there will be no visual damage and the ca- pacitors will meet the limits of the table below. bending test: solder attach the capacitors to printed-circuit boards. suspend each board between two edges separated 3.5 inches with the capacitor in the center and on the underside. press in the center of the suspension until the board flexes downward 0.1 inches. there will be no visual damage and the capaci- tors will meet the limits of the table below during and after the bend- ing. moisture resistance: subject the capacitors to 40 2 c at 90 to 95% humidity for 500 (+24,C0) hours. return to room ambient for 24 hours. there will be no visual damage and the capacitors will meet the limits of the table below. temperature coefficient and drift: measure the capaci- tors capacitance at 25 c, C55 c, 25 c, 125 c, and at 25 call 3 cafter stabilizing at each tem- perature. the capacitance will meet the limits of the characteristic table in ordering information. heat resistance: subject the ca- pacitors to 125 2 c for 2 (+1,C0) hours. then the insulation resis- tance will be no less than 5g w . solderability: after 2 0.5 sec- onds in molten solder with 2.5% sil- ver at 270 5 c, solder coverage will be no less than 90% when exam- ined at 10x magnification for flow soldering and no less than 75% for reflow soldering. solder heat resistance: sub- ject the capacitors to molten solder as above with 5 minutes preheating at 150 3 c. there will be no visual damage and the capacitors will meet the limits of the table below. test withstand insulation capacitance df q voltage resistance (whichever >) life test il il iv 2% or .5pf 150% max il 2/3xil vibration resistance il 30 g w iv 1% or 1pf il il bending test il iv .5% or 1pf il moisture res. il 30 g w iv 3% or .5pf 150% max il 2/3xil solderability il il il il il heat resistance 5 g w solder heat res. il 30 g w iv .5% or 1pf il il il=initial limit iv=initial value after-test limits example: r1 = 43 pf il=initial limit 8942 1.030-1.034 4/3/2000 6:17 pm page 32
1605 east rodney french blvd. new bedford, ma 02744 (508) 996-8564, fax (508) 996-3830 http://www.cornell-dubilier.com e-mail: cdenb@cornell-dubilier.com 1.033 chip and smt capacitors cornell dubilier your source for capacitor solutions type mc, surface-mount mica chip capacitors ordering information order by complete part number, as below. for other options, write your requirements on your quote request. surface-mount chip mica capacitors mc 22 f d 122 j C t cde case voltage capacitance type code a = 100 vdc 010-1pf d = 500 vdc 1r8=1.8pf f = 1000 vdc (187)=187pf 182=1800pf characteristic char capacitance temperature capacitance code range pf coefficient ppm/ c drift tol. code tolerance capacitance range c 0.5 to 10 100 100 (.5% +0.1 pf) b 0.1 pf 0.5 pf to 10 pf e 10.5 to 30 50 50 (.1%+0.1 pf) c 0.25 pf 0.5 pf to 99.5 pf f 30.5 & up 25 25 (.05%+.1 pf) d 0.5 pf 0.5 pf to 10 pf f 1 pf 0.5 pf to 10 pf c 0.25% 100 pf and up d 0.5% 50.5 pf and up f 1 % 25.5 pf and up g 2% 13 pf and up j 5% 10.5 pf and up capacitance tolerance available capacitance values capacitance, pf minimum case cap. code 100 vdc 500 vdc 1000 vdc step, pf 08 0.5 to 43 n/a n/a 0.5 12 43.5 to 100 0.5 to 100 n/a 0.5 12 101 to 430 101 to 150 n/a 1.0 12 1 to 50 1.0 18 250 to 820 100 to 470 n/a 1.0 22 821 to 1000 471 to 1000 n/a 1.0 22 1010 to 2000 1010 to 1200 100 to 1500 10.0 standard minimum shipping quantities reel packed case codes 08 & 12: 3,000/reel case codes 18 & 22: 1,000/reel bulk packed 100 per bag case sizes inches millimeters case case i i code type l w h min/max l w h min/max 08 0805 .079 .049 .055 .008/.035 2.0 1.25 1.4 .2/.9 12 1210 .126 .098 .079 .012/.043 3.2 2.5 2.0 .3/1.1 18 1812 .177 .126 .079 .012/.051 4.5 3.2 2.0 .3/1.3 22 2220 .224 .197 .079* .012/.051 5.7 5.0 2.0* .3/1.3 +.02 C0 +.024 C.004 +.024 C.008 +.016 C.012 +.02 C0 +.024 C.004 +.024 C0 +.016 C.012 +.5 C0 +.6 C.1 +.6 C0 +.4 C.3 +.5 C0 +.6 C.1 +.6 C.2 +.4 C.3 010 = 1pf 1r8 = 1.8pf (187) = 187pf 182 = 1800pf length width solder-coated nickel/silver termination height i i package leave blank for bulk add Ct for reel or tape *.157 (4.0 mm) for 1000 v rating 8942 1.030-1.034 4/3/2000 6:17 pm page 33
1605 east rodney french blvd. new bedford, ma 02744 (508) 996-8564, fax (508) 996-3830 http://www.cornell-dubilier.com e-mail: cdenb@cornell-dubilier.com 1.034 cornell dubilier your source for capacitor solutions chip and smt capacitors type mc, surface-mount mica chip capacitors surface-mount chip mica capacitors for auto insertion .078 .02 (2 .5) .83 .03 (21 .8) .51 .02 (13 .5) 3.15 (80) 7.0 .08 (178 2) p 1 p 2 p 0 t t d b c d carrier dimensions item symbol case code 08 12 18 22 sprocket hole pitch p 1 .157 .008 (4.0 0.2) sprocket hole location b .069 .008 (1.75 0.2) hole center to cavity center c .138 .002 (3.5 0.05) .217 .004 (5.5 0.1) carrier tape width d .315 .012 (8.0 0.3) .472 .012 (12.0 0.3) sprocket hole diameter d .059 (1.5 ) cavity pitch p 0 .157 .004 (4.0 0.1) .315 .008 (8.0 0.2) hole center to cavity center p 2 .079 .004 (2.0 0.1) cavity length l .110 (2.8 ) .150 (3.8 ) .205 (5.2 ) .246 (6.25 ) cavity width w .075 .008 (1.9 0.2) .118 .008 (3.0 0.2) .161 .008 (4.1 0.2) .217 .008 (5.5 0.2) cavity depth t .051 .004 (1.3 0.1) .059 .004 (1.5 0.1) .071 .004 (1.8 0.1) .087 .004 (2.2 0.1) carrier tape thickness t .012 .002 (0.3 0.05) holder distance w 1 .354 (9.0 ) .512 (13.0 ) reel thickness w 2 about .47 (12) about .63 (16) +0.2 -0.1 +.008 -.004 +0.2 -0.1 +.008 -.004 +0.2 -0.1 +.008 -.004 +0.2 -0.1 +.008 -.004 +.002 -0 +0.1 -0 +.08 -.02 +2 -0.5 +2 -0.5 +.08 -.02 l w w 1 w 2 .078 .02 (2 0.5) 8942 1.030-1.034 4/3/2000 6:17 pm page 34
|
